Commercial ยท Panic Bar Installation
Exit door not locking right? Panic bar installation
A push bar that sticks, or an exit door that needs one? Across 12 Mid-Missouri counties.
- Mortise locks
- Back doors
- Cylinders
- Storefront doors
- Office doors
- Keys
Panic Bar Installation
Panic Bar Installation, step by step.
What this covers
A panic bar sits across the push side of the door, with the crossbar, latch, and trim set for a clear exit. We install new exit devices on commercial doors and adjust ones that scrape, stick, or sit loose at the latch. We also repair bars with a broken push pad, a bent rod, or a latch that will not catch cleanly. You see the bar, the door face, and the latch opening. We fit the parts to that door, not to a general layout.
How the work goes
Each job starts with the door in front of us and the way the bar meets the strike. A narrow metal door needs a different setup than a wood door with a bored opening. A rim device, a mortise device, or a narrow stile unit can all ask for a different fit at the edge and the latch point. We check the push action, the latch travel, and the closer pull, then set the bar so the door opens from the push side without dragging.
Where it stops
We do not handle code promises or fire door certification. If the bar is bent, loose, or failing at the latch, we work on that part of the door and the exit device itself.
What it covers
What panic bar installation covers
Panic bar installation, exit device adjustment and repair.
Worth knowing
Before you call about panic bar installation
If you can describe the bar on the door, we know where to start. Tell us if it is a touch bar, a crossbar, or a narrow push pad. Say whether the lever sags, the latch drags, or the inside trim feels loose. If the bar sits high, low, or uneven, we look at the mounting screws, the latch case, and the strike first. A bent rod, worn latch, or loose end cap changes which parts get checked before the cover comes off.
The details around the door edge help us narrow the first inspection. If you see a gap at the strike, a latchbolt that sticks out, or a bar that rubs before it moves, say that on the phone. We start with the latch, the strike plate, and the face of the exit device. A missing screw, a cracked cover, or a twisted actuator changes which fasteners we check first. If the bar moves but the latch does not, we look deeper into the case and release parts first.
When the bar is on a rim, mortise, or bored cylindrical setup, the outer shape tells us what to inspect first. If you can name the style, and say whether the key turns but the bar will not release, or the bar releases but the door still binds, that points us toward the cylinder, spindle, or latch body first. A loose trim ring, a stiff thumbpiece, or a bent handle changes the order of the checks. We start where the motion feels wrong, then work through the moving parts on the door.
FAQ
Panic Bar Installation questions
My exit bar is hard to push and the door still feels like it catches. Is that usually the bar itself, or something else?
It can be the bar, but the latch, spring, or dogged-down part may be dragging too. We look at the push bar, the latch end, and the way the latch clears the strike. If we only free the sticking spot, the rough movement can come right back when the worn part keeps binding.
If my panic bar is loose or rattles, do you fix that or replace the whole thing?
We can adjust loose screws, worn fasteners, and a sagging touchpad, or replace damaged parts when needed. A rattle often comes from movement in the mounting points or an internal spring that no longer holds tension. Tightening only the visible piece can leave the same shake and noise in the bar.
When the door opens but the latch does not fully catch, what are you checking?
We check the latch bolt, the strike, and the alignment of the bar with the door edge. A weak return spring or a bent latch part can stop the bolt from seating all the way. If we only move the strike a little, the same sticking can show up again as the parts shift.
If my panic bar was repaired before and the problem came back, what causes that?
The cause is often wear in the latch, the spring, or the mounting screws, not just the symptom you notice at the bar. We look for the part that keeps creating the bind, because easing one stiff spot without fixing the worn piece lets the same trouble return at the push bar and latch.
Related services
Related to panic bar installation
Where
Panic Bar Installation across Mid-Missouri
12 counties and 101 towns. Pick your county to see its towns.
Coverage