Commercial ยท Commercial Lock Installation
Fitting out a business? Commercial lock installation
New locks for a storefront, office or back door? Across 12 Mid-Missouri counties.
- Back doors
- Cylinders
- Storefront doors
- Office doors
- Mortise locks
- Keys
Commercial Lock Installation
Commercial Lock Installation, step by step.
What this covers
We install business door locks for storefront and office doors across Mid-Missouri. You may have a knob set on a glass entry, a deadbolt on a side door, or a mortise lock in a narrow metal frame. We fit new locks where the old cylinder wobbles, the key feels rough, or the latch no longer meets the strike cleanly. We work on rim, mortise, and bored cylindrical locks, and we set the parts so the key turns in the door you already use.
How the work goes
The work starts with the door and the way it closes. A glass storefront with an aluminum stile needs a different lock than a solid office door with a keyed lever. We look at the bore, the latch, the face of the door, and the spacing around the existing holes before we install anything. Some jobs call for one lock at the main entrance. Others need matching locks on several doors, each with its own keyway and latch setup.
Where it stops
We do not cover code claims or networked access systems. If your door needs a card reader or other wired entry setup, that is outside this service.
What it covers
What commercial lock installation covers
Business door lock installation, storefront and office locks fitted.
Worth knowing
Before you call about commercial lock installation
If your door has a rim lock, we work with the round case on the face of the door and the night latch above it. We check the cylinder hole, the tailpiece, and the rim cylinder outside. If the inside thumb turn is loose or bent, we replace that part and reset the mounting screws. On some doors, the strike plate sits high or low on the jamb, so we match the latch throw to the keeper already there. The surface parts stay in place while we fit the new lock.
A mortise lock changes the job because the case sits inside the door and the faceplate shows only a narrow strip at the edge. We remove the trim, pull the old cylinder, and check the lock case for wear at the bolt and latch. If the trim ring is scarred or the thumbpiece binds, we replace those pieces and fit the new set to the same opening. The spindle and lever lines have to match what is already in the door. We set the new cylinder in the pocket and secure the faceplate.
With a bored cylindrical lock, the round holes through the door decide most of the work. We check the knobs or lever trim, the latch body in the edge bore, and the cross bore for spacing. If the existing trim is loose, we adjust the mounting screws and change the latch parts that sit in the door edge. When the outside cylinder is keyed differently from the inside side, we fit the new keyed piece to the same trim set. The latch tongue and the rosette stay aligned with the holes already drilled in the door.
FAQ
Commercial Lock Installation questions
What kind of commercial door lock should I ask for on my office or storefront door?
The right choice depends on the door and the key control you want. We fit rim locks, mortise locks, and bored cylindrical locks on business doors. We also match the latch, cylinder, and keying plan to the door you have now. That keeps the face of the lock, the keyway, and the thumbturn working together.
How do I know if my business door lock needs replacing instead of another repair?
We look for a loose cylinder, a latch that drags, a key that sticks, or a thumbturn that feels gritty. If the key is worn or the faceplate is bent, a new lock may make more sense. We compare the door, the key, and the strike area so the new parts fit the opening cleanly.
What should I do to keep the same key or lock problem from coming back?
Keep the key clean and avoid heavy key rings that pull on the cylinder. If the key starts to catch, stop forcing it and check for wear on the cuts or bends. A small amount of graphite can help some keyways, but oil can attract grit. We can also look at the latch and keyway before wear gets worse.
What do you need to see before installing a new commercial door lock?
We need to see the door edge, the face of the existing lock, and the key that opens it now. That lets us match the backset, the bore, and the latch style with the new lock. If the old cylinder or thumbturn is worn, we can replace those parts and set the new keying for the door.
Related services
Related to commercial lock installation
Where
Commercial Lock Installation across Mid-Missouri
12 counties and 101 towns. Pick your county to see its towns.
Coverage